This collection is a bit more “odds and ends” with some focus on sample and holds as modulation complicators and as performance tools. It is the last installment in my epic series on the sample and hold module, complementing the previous entries: https://patchstorage.com/s-and-h1-basics-a-patch-to-complement-my-video-on-sample-and-hold-basics/ and https://patchstorage.com/sandh2-sequence-a-patch-to-complement-my-video-on-sample-and-holds-as-shift-registers-and-sequencers/.
It’s a little harder to summarize the contents of the patch, or the video, because the “odds and ends” nature, but the descriptions of the little patchlets may help you appreciate their use. The series is not, by any means, meant to be an exhaustive exploration of the sample and hold (although it was exhausting to produce); you could think of it like this: the first entry introduced the module and some useful conceptual frameworks for working with it, the second entry delved into the complex apparatuses that could be constructed from sample and holds, and this third entry takes a look at the sample and hold as a more practical “problem-solving” module.
That said there are still countless more applications of the module, I’m sure. But hopefully the series will give you some insight into how to use the sample and hold to solve problems not covered in these videos as well.
Pages:
“Super slow LFO” (0)
On this page are two LFOs, almost operating at the same rate, to produce a super-slow LFO, as one LFO feeds the sample and hold and the other clocks it. (I learned this approach from Willem Zenhorst.)
There is a value module to control the speed of both LFOs and therefore the aggregate LFO. You can also adjust the connection strength from the value module to the LFO (currently, the square clock is connected at 100% and the sine source is connected at 100.1%) to affect the speed of the LFO.
Also on this page is an oscillator, used for demonstration purposes. A pushbutton controls the outputs of its VCA. Along the bottom is a four-input switch for selecting what mod source affects the oscillator across a one-octave span — this super slow LFO, the next super slow LFO, a “chopped” LFO, and a stepped LFO.
“Super slow LFO2” (1)
No LFOs at all on this page. Instead, a clocked sample and hold counter creates a super slow triangle wave. The sample and hold is fed back upon itself and also fed with either a positive increment value or a negative decrement value.
The output of the sample and hold is connected to two comparators to go high either as the sample and hold reaches 1 or 0; upon doing so, the comparators flip the state of a flip flop, so the counter increments or decrements between 0 and 1.
On the bottom is the value used to set the incremenet/decrement amount. You can affect the rate of the LFO by either changing the increment amount or the rate of the LFO clocking the sample and hold at the top of the page.
“Chopped LFO” (2)
Like the LFO used in the Demedash T-60, this LFO is “chopped” by a sample and hold. (Conceptually, it’s very possible and often exploited in eurorack to think of a sample and hold as a sort of bit reducer, since the fidelity of the input is controlled by the speed of the trigger input/clock source.)
The approach is pretty simple: the triangle wave LFO feeds the input of the sample and hold while a faster square wave LFO (there is a pushbutton to set a tap tempo) “chops” the wave by triggering the sample and hold at a faster rate.
I included a steps module to demonstrate the difference between the approaches (a steps module’s reduction is always the same, while, because the time-relation between the input modulation and the clock/chopping LFO in this example may not be inherently related, the chopped wave produced will be less regular and more “organic” or unpredictable.)
“Tap or CV” (3) // Automatic tap or CV selection
This technique allows one to choose between using CV or tap (used generically here, as Empress does, to mean any sort of clock/pulse: tap tempo, but also MIDI clock, CV clock, etc.) for controlling destinations like delay time, LFO speed, the rate of a modulator effect, etc..
I’ve written a fairly thorough explanation of this circuit on Tips and Tricks, so I’m not going to repeat it here: empresseffects.com/zoia-tips-and-tricks
“Seq edit” (4-5) // Editing sequencer steps before going live with them
Here, track and hold modules (an edit option for the sample and hold module) are used to create a way to edit sequencer steps before they go live. Value modules connect to the inputs of the track and hold modules, and the track and hold modules subsequently connect to the inputs of the first track of a sequencer (connections to sequencer steps are only possible on the first track).
When the track and holds are high, the steps can be edited without being heard; then, the track and holds can be released and the new edits to the sequence will go live.
I added a gate track to the sequencer, connected to a sample and hold’s trigger input. A pushbutton is connected to the sample and hold’s input. The output of the sample and hold controls the track and holds.
A demonstration using a mod delay module is set up on page 5. A pushbutton there will mute and unmute this demonstration voice.
“T and H mod” (6-7) // Using a single mod source (e.g. expression pedal) to control multiple parameters / using track and holds to preserve the parameters when the mod source switches to other destinations
This is an exploration of how to direct a modulation source, such as an expression pedal, to multiple destinations. You can do this with an out switch, but when the expression pedal is switched off the destination, the connection drops back to 0. Using track and holds in series with the output, you can maintain the position the modulation source was at when it was switched to a new destination.
A sample and hold counter (a sequencer could also be employed) changes the channel of the outswitch while, in parallel, another outswitch sends values of 1 to the track and holds’ trigger inputs when they are not active, preserving the output at the level it was when the modulation source was switched to another destination.
A pushbutton cycles the sample and hold counter, changing the active channels on page 6.
A demonstration using a mod delay module is set up on page 9. A pushbutton there will mute and unmute this demonstration voice.
“Catch-up” (8) // creating a value catch-up option for held values (so a stored parameter won’t change until the modulation source reaches the stored value)
Although the previous example solves one aspect of using a modulation source to control multiple parameters — i.e. maintaining their levels once the modulation source is switched off from them — a new one arises: when the modulation source does return to a new output, it is often different from the stored level, resulting in jumps.
This page demonstrates a technique for creating a “catch-up” method, often employed in synths and some pedals that have presets, where the modulation source won’t become active again (or rather, the track and hold won’t be released), until the current output passes (catches up with) the stored setting.
To do this, the output from the out switch is compared against the stored value of a track and hold; when it passes higher or lower than the stored value, one or the other of a set of comparators will go high, producing a trigger that releases the flip flop controlling the track and hold.
The flip flop also controls an in switch, so that when it goes low, releasing the track and hold, the triggers from the comparator/trigger combinations can no longer change its state. It’s locked in place again by the out switch on page 7 from the previous example.
“Demo delay” (9)
The demonstration voice used to in the previous two examples.
“Interp. shft reg” (10-11) // interpolating shift register, a cool, evolving modulation source
This is an interesting approach to the idea of the shift register as a modulation source, rather than employed in note generation. Rather than holding a series of discrete values, this ‘interpolated’ shift register constantly glides between the values produced, with a time constant slew.
The basic principle remains: a series of sample and holds, joined output to input, with a switch controlled by probability determining whether that series is looped back on itself or a new value is introduced into the series.
However, here the clock for the sample and holds is a ramp LFO, rather than a square LFO.
We can take the output of two, adjacent sample and holds and determine their difference by adding the more recent stage to the inverted value of the older stage. We can then multiply this by the ramp LFO itself to produce a constant time slew when we add the output of the multiplier to the output of the older stage. The values will glide from one step to the next. By adding more copies of the LFO to the multiplier, we can affect the curve of the slew as well.
The result is a complex, evolving modulation source (this could also be a candidate for a super slow “LFO”) that is neither entirely random, nor predictable.
“Knob record” (12) // a method of recording knob movements and scaling them for their destination
This technique allows one to record the output the knob (via a value module) with a CV looper and scale it appropriately using a sample and hold to create a reference position, so when the recording is added to the value module’s destination, it accurately reflects the movement of the knob during recording.
I’ve written a fairly thorough explanation of this circuit on Tips and Tricks, so I’m not going to repeat it here: empresseffects.com/zoia-tips-and-tricks
